4392067RC 27-Inch Dryer Repair Kit 4392067VP for Compatible with Whirlpool Ken-More,PS373088 AP3109602, Include 279640 Idler Pulley W10314173 Drum Roller 661570 Belt

I ordered this instead of buying just the replacement belt & I'm glad I did. The rollers in the dryer had lint all over them & were so tangled up they couldn't spin. In fact the belt on my dryer was fine, it was the rollers that kept the drum from spinning. I cleaned out all the lint and installed the new parts, probably took 15 mins. Make sure when you put it back together that the wires don't get pinched. I had to repair the wires from the previous repairman. The red wire was melted to the white wire and the black and ground both had bare wire showing. It would have cause the whole dryer to short out, glad I caught it. I would also recommend having some foam weather striping for replacing the deteriorate one that yours will likely have. That's why the lint was all inside the dryer to begin with. The weather striping on my was basically gone.Tools:1/4" socket on a drillFlat headed screwdriverSpray cleanerPaper towels

This is a great product that cameExactly as described. The addition of the wheels made it even better as it allowed me to replace the belt, idler wheel, and wheels while I had it apart. The idler wheel was a tight fit, but is supposed to be by design so there is no wobble. With a family of 5 plus my son, daughter in law, and their 3 little boys in the house right now, it is getting plenty of work. It continues to run great and quiet. I have a Kenmore dryer, so can’t speak for other brands as to the fit.

Backstory; A friend bought this dryer at best buy, and sold it to me for $20. (Apparently there was a dent, and best buy said they wouldn't accept it.) This thing has worked great for ~6 years. However, one day.. the motor stopped turning + wouldn't heat up anymore, even though the control timer ticks. (Note; The thermal cutoff switch next to the motor fan had blown.) Needless to say, I thought it was time to replace the wheels, belt, and pulley.Parts needed;1/4 inch socket or wrench to loosen generic bolts9/16" or 15 mm wrench for pulley nutsPozidrive #2 screwdriver for the bolts on either side of the front cluster...Small needle nose pliers to pull triangle washers off/onT20 Torx to remove 2x bottom door screws (really??)PH2 for 5x bolts for the lint collectorScissorsWhite lithium NLGI #2 grease (optional)#8 by 1/2 inch stainless bolts (optional ... note, my washer used zinc coated steel bolts, so they're slightly oversized... might want to use #9 by 1/4 inch stainless steel bolts instead...)New belt was alot thicker, slightly shorter, and the pulley has a bigger diameter. Meaning with this kit, it will add some more tension to the motor. (Good in my case.)My wheels had about 6 hundredths of a mm of wear, the belt pulley has scoring on the inside, and the same 6/100ths mm of wear.My overall thoughts.. they should have included replacement shafts as well, I read about 1/100th mm of torsional wear on my back wheels. Because this isn't my first rodeo, I put some grease on the shafts.. I'm hoping that will reduce wear on them.Note: My Dryer Drum seal is real bad, and probably contributed to the unit overheating.. might we worthwhile to try scraping it off, and applying a new one on both ends. On my dryer it seems to be Whirlpool part 280114. (You'd have to buy two, only comes with one strip it seems.

This worked for my whirlpool wed5610xw0 dryer. I felt the rollers went on the posts pretty tight, so I added a light wipe of high temp break grease I had lying around. Time will tell if it doesnt like the grease. In the mean time my squeak from the pulley is gone, the belt was not too tight, but the pulley is certainly as far back as I could get it, so there is plenty of space for the belt to relax as it breaks in. It's been two months since install and I'm happy.

This product saved me a lot of $$. If I had to buy new it would have been expensive. If I had someone come repair it same results. You have to read instructions and become familiar with removing and installing parts. After that my dryer is working like new. Plus it gave me an opportunity to totally clean the entire dryer of lint, sand and dirt.The belt was a few inches longer than my old one, but since it is on a tension spring it fit just fine.Definitlet worth the money !!

Does NOT fit MAYTAG NEPTUNE dryer mde9700ayw!!! I saw in one of the answered questions that it would so I bought it. The Belt DOES fit. However, the wheel/pulley replacements are just a hair to small. I was able to clean the shafts with brake cleaner and get the pulley and wheels rolling freely so I was able to put my dryer back together. I did not deduct stars because, to be fair, the manufacturer never said these would fit my dryer and all of the included products were of good quality and arrived the day after I ordered them.

My dryer was making a loud thumping noise, so I thought the rollers went bad and bought these. I'm a handy guy but this still took about 2-3hrs to replace and I certainly needed a shower after doing so (the inside of your dryer is disgusting, FYI).The sad part for me was that it appears my dryer drum is the root cause of my "thumping". Oh well - it's my bad for not troubleshooting enough, not the kit's. It did definitely sound "smoother" though. One month later, these are still holding-up.

The wheels disintegrated within a couple years whereas the oem ones lasted nearly 20. These wheels are thinner and softer and far less durable than oem.